First, install the software and use conditions This software is a non-installation type of snapshot software, directly copied to the root directory of the system disk, create an executable program on the desktop shortcut can run. The picture preview area shows: capture the panorama of the vehicle (red light close-up) and license plate composite picture, and superimpose related information; Use Ctrl+Shift+F12 to bring up the settings window as shown above. hammer mill, also called hammer crusher, hammer mill crusher, impact hammer crusher machine, is mainly used for crushing medium-hard or brittle materials with hardness not more than 300Mpa and 15% moisture,such as coal, cement,gypsum,alumen,brick,tile,limestone,etc.It has the features of simple structure, big crushing ratio, high production efficiency, uniform particle size, etc. This equipment can be adjusted to reach various discharged granularity as the customers' requests. Hammer Crusher,Gold Hammer Crusher,Crusher Hammer Machine,Stone Hammer Crusher henan ascend machinery , https://www.ascendminingcrusher.com
Software use conditions:
n Operating system: windows2000pro+sp4/windows XP/windows XPE
n Application graphics acceleration: directX8
n Grabber application: Install Daheng card parameter setting program Multicard Performance.exe in Daheng Imavision CGCard
Note: Only after clicking the 'Save' button, the system prompts 'Saved Successful' and exits after restarting the application. These settings will only take effect!
Second, the environment settings
1, the acquisition card configuration:
Run Multicard Performance.exe program Select 'Allocate Memory' in 'Paramter' and set the parameter to 10000 in the popup setting window.
2, run the program and configure the capture environment (1) run the program click on the desktop 'VideoSystem.exe' program icon, the program opens the capture preview and interactive information interface, as shown below:
Image preview area information area
The information area shows: detection information, direction attributes, and vehicle speed information of the software and hardware system that the program started;
(2) Configuration of snapping environment The setting of snapping environment is divided into two parts: intersection direction setting and basic system setting.
A, intersection direction setting type selection video preview area
Road selection: Select the direction, number of lanes, and whether to use red lights for the current camera. When one direction is selected, the configuration of the lower [direction 2] does not work, and only the direction 1 can be configured.
Acquisition card number: used to adjust the settings when using multiple acquisition cards.
Direction, lane and number of cameras: The system automatically generates corresponding values ​​corresponding to 'road selection';
Channel, address code: for camera video correspondence and control settings, usually use the default value;
Location code: Code the lanes individually to capture data for lane recognition;
Red light close-up: This item will be checked by default when red light close-up is selected in traffic conditions;
Control port COM1: RS232 control port for setting direction 1;
B. System Basic Settings The basic configuration window of the system is shown in the figure below:
Behavior code: used to define the type of electronic police illegal capture;
Retrograde detection: whether to enable retrograde detection;
Watchdog startup: embedded watchdog startup to prevent abnormal operating system and application operations;
Start disk rotation: whether to start the disk cycle for data storage cycle;
Start download service: whether to start the download program, download the program corresponding bayonet data and illegal data;
PC mode and embedded mode: The default is PC mode. When using the embedded capture card VT121, you need to select the embedded mode;
Area display: whether the video detection area is displayed and does not work when the coil is detected;
Threshold: The sensitivity setting of the video detection does not work when the coil is detected.
Characters, up, down and no overlay: set the position of the character overlay;
Start video/coil detection: Set the detection mode of the capture program, only one can be set;
Launch bayonet function: After starting this item, the snapping process not only captures the illegal snapping but also the bayonet record, which can detect and capture each vehicle passing through;
The entire field, 1/2 field acquisition: is the setting of the number of video preview frames, in order to facilitate the smooth video image when debugging the camera;
Coil distance 1~4: It is used to set the actual coil's precise distance, and it is used for speed measurement system.
Image generation path: used to specify the drive letter and directory of the snapshot data storage;
Superposition intersection name: This paragraph can be set according to the need for character superposition content;
Third, capture settings Capture settings are divided into two parts: system program settings and signal status settings.
1. System Solution Settings Before setting the system solution, you need to select the opposite of the settings, as shown in the following figure:
For unidirectional setting, direction selection is not needed. When the system defaults to the direction of 'Direction[1] section' in both directions, the camera's corresponding direction is to select 'Direction[2] section'.
The camera that needs to be debugged can be video-capable by clicking on the name of the camera. In the video preview window, you can directly see the adjustment effect of the real-time video in this setting.
as the picture shows:
Brightness, contrast, saturation, chroma value and setting values ​​are all used for the video adaptation of the camera. It is defined according to the experience of the debugger and the historical reference value.
The scheme is used to save a set of values ​​set by the current system to facilitate switching in debugging;
State 1~8 is used for the video response in camera video detection and the effect of fine-tuning video detection;
2, the signal state set the signal state is set to two parts: the red light signal corresponding to the azimuth state and car inspection signal diagram. As shown below:
(1) The red light signal corresponds to the azimuth state. Please refer to the relevant contents of the red light program in the "Red Light Signal Encoder Manual". (2) The car detection signal diagram shows the square wave of the current access coil being triggered, and the trigger sequence. For debugging and auxiliary testing to determine the use.
Fourth, the software exits and unloads The software only needs to delete directly to be able to actually uninstall the operation.
Right click on the snapshot icon and select 'Close' to exit the snapshot.
Fifth, download the configuration data download program DownLoadServer.exe, and the capture program in the same directory, when the capture program starts and select the 'start download service' case, the download program can be executed after the capture program starts, and in the lower right corner The Run icon is displayed in the System box.
Right click on this icon and select 'Configuration'. The following configuration window appears:
Perform port configuration for 'port number' and click 'save' to set it up successfully. Restart the download program and the configuration is applied.
Right-click on this icon and select 'Close' to close the download process.
VI. Common Faults 1. The information area of ​​the capture program prompts 'system initialization failed'
Normally, the acquisition card driver is not installed, the acquisition card is driven abnormally, or the acquisition card is damaged. By reinstalling the driver and replacing the acquisition card, the program can run normally.
2, when running the download program prompts 'setting is not normal, please run this program after correct settings'
This is because the configuration file of the download program is corrupted or lost. Under normal circumstances, you can cancel this error by simply running the download program again.
3, the information area of ​​the capture program indicates that the direction [1] failed! Port [1] failed"
When the program is started twice, this prompt may appear, that is, the first time the program did not quit completely, and the second time the program was executed again. From the lower right corner of the system status box, you can see two snapping program icons. A startup snapshot program will have this prompt.
Processing: Exit the download program first, and then exit the capture program one by one, which can solve this problem.
4, Snapshot program information area prompt 'System is not registered'
In the case of program startup, use Ctrl+Shift+F4 to call up the registration window, return the machine code in the window to the company's technical department to apply for registration, fill in the registration code obtained and click.