(1) The cutter rigidity is better First, the need to use a large amount of cutting in order to increase production efficiency; second, to adapt to the characteristics of difficult to adjust the cutting amount in the process of CNC milling machine. For example, when there is a great difference in the machining allowances in various parts of the workpiece, the general-purpose milling machine can easily solve this situation by adopting a layered milling method, and the numerically controlled milling must proceed according to the path specified by the program and meet a large margin. It cannot be "strained" like a general-purpose milling machine, unless it can be considered in advance when programming, otherwise the milling cutter must return to the origin and start machining from the beginning by changing the cutting surface height or increasing the tool radius compensation value. However, this will inevitably lead to the use of empty knives in places where the margin is small, which will reduce the production efficiency. If the tool rigidity is better, it is not necessary to do so. In addition, when machining on a general-purpose milling machine, if it encounters a tool that is not strong enough, it is easier to detect and timely adjust the cutting amount from the aspects of vibration, feel, etc. to make up for it, and it is difficult to do when CNC milling. In the case of numerical control milling, it is often the case that the tool is broken and the workpiece is damaged due to poor rigidity of the milling cutter. Therefore, it is very important to solve the rigidity problem of the numerically controlled milling cutter.
Fast PVC rolling door can be designed according to the needs of customers. These doors can be used in firms, inside or outside. The fact that it is not used on a fixed area provides a flexible usage possibility. According to the needs of the firms, they can easily choose PVC rolling doors in the building areas. In addition, it can be used in exterior areas and provides a wide usage area. Fast PVC rolling door can be produced by coating fabric. The different colors of the fabric can be helpful in separating parts of the business. The function of the tarps is not only aesthetic, but also contributes to the protection of the door system against impacts. Since the impacts of the fabric do not come into direct contact with the door surface, it is inevitable that the door will be protected and long-lasting. The fabric can be a very important material so that the door receives as little damage as possible from impacts. Of course the fabric is resistant to a certain level of impact and there is also the possibility of damaging the fabric. You can contact our company for repair of PVC Fabric Roll Up Door. Standard: 0.7 m/s It can be increased up to Maximum opening: 1.5 m/s Maximum closing: 0.4 m/s Aluminum wind rail: 35km/h Brands: Mehlar, Heytex, Sioline Thickness of normal fabric: 1 mm Thickness of transparent fabric: 2mm Manually Operated Optional: It can be operated with UPS in case of power eut Sides struts, lower parts, wind rails, and drums are aluminum. Sides of the upper parts are coated with galvanize. Winding box is 1311 galvanized. Reducer box Fast PVC door motor set (Temporiti-ITALY) DH-14 Door controller Pepperl fuchs safety photocell Rovioly Limit system
PVC Rapid Roll Up Door, high speed roll up doors, PVC fast rolling doors SHENZHEN HONGFA AUTOMATIC DOOR CO., LTD , http://www.hongfafrs.com
(2) The durability of the milling cutter is higher. Especially when a milling cutter processes a lot of content, if the cutter is not durable and the wear is rapid, the surface quality and machining accuracy of the workpiece will be affected, and the change caused by the tool change will be increased. Adjusting the number of knives and counters can also cause the work surface to leave a knife step caused by tooling errors, which reduces the surface quality of the workpiece.
In addition to the above two points, the selection of the geometrical parameters of the cutting edge of the milling cutter and the chip removal performance are also very important. The formation of the built-up edge of the saw blade by the cutting blade is very scary in the numerical control milling. In short, according to the heat treatment state of the workpiece material being processed, the cutting performance and the machining allowance, the selection of a milling cutter with good rigidity and high durability is a prerequisite for making full use of the production efficiency of the CNC milling machine and obtaining a satisfactory processing quality.